Alrowad Complex is one of the leading Egyptian companies working in plastic industry
specialized in designing and manufacturing HDPE pipes and fitting by using the best raw material and developing the highest technology and quality applied in this field, as It’s production capacity reach to 6000 tons per month.
Our company also develops our products from pipes and Fitting to serve many sectors such as potable water networks, sewage water networks, infrastructure projects, natural gas, firefighting lines... etc.We are providing technical support for all stages of the projects
TAHA ALGAMMAL
01.
ALROWAD SOLUTION
MICRODUCT Bundles
Microducts are small diameter conduits ranging from 5-28 mm OD that provide a pathway for fiber cables. They are suitable for use in network applications such as FTTH (Fibre to the Home), FttB (Fibre to the Building), FttC (Fibre to the Curb) or the last mile.
02.
ALROWAD SOLUTION
MICRODUCT WITH TRACE WIRE & RIP CORD
Multiple pathways for one installation cost, allows flexibility and future growth
No special tools or equipment needed; installation uses the same as traditional conduit or innerduct
Choose the correct MicroDuct size based on the Outer Diameter (OD) of desired MicroCable. Dura-Line recommends a fill ratio of 50% to 75% for optimal cable placement performance. Several factors impact jetting distance, including the condition of route, bends, and equipment.
03.
ALROWAD SOLUTION
MICRODUCT Accessories
End Caps
Introduction
End Caps: is used for quick and easy tighten the ends of unused primary tube. Provides water resistance and mud resistance. It is also used in
combination with the valve end stop connector during installation of micro ducts into existing cable ducts.
Application:
The end cap for permanent or temporarily sealing of unused microducts to prevent obstacles such as water, mud, dust an so on.
Features:
The End Cap are tested for best functionality in combination with the air blown fibers unit and air blown fibers cables. •Easy “push-in” installation
•For 3 to 20 mm O.D. microducts
•Material: Clear PC
•Leakage Pressure: 15 bar •Negative Pressure: 750mm Hg •Proof Pressure: 25 bar •Temperature Range: -10 ~60 
FTTH BOX
Distribution Point Ftth Box (DP) is designed for use in residential and business applications for the termination of up to sixteen optical fibres/drop cables. The DP can be used as a passive splitter housing of up to 1 x 8. Within the DP box there are splicing cassettes for splicing the Distribution cable to the drop cable in the case of point to point or from distribution cable to the passive splitter whereby the fan out of the passive splitter then spliced in the cassette or terminated at the adapter coupler. The unit is supplied with a fixing bracket for pole mounting. The unit is supplied with a lockable hinged door and a rubber seal providing an IP rating of 65
Product Features
- - Compact and Robust design
- - 2 Cables entry trough the bottom with security glands
- - 16 ports for drop cable outlets with rubber glands
- - Pole and wall mounting
- - Splicing trays with fussion splice protector organizer and splice tray cover
- - Standard color is white RAL9016
- - Splice tray with locking magnet
Part Number
| Description | SC/UPC | SC/APC |
| Empty | OPVL-DP-1000 | |
| 4 Pigtails G652D 1m & 4 SC Adapters | OPVL-DP-1104 | OPVL-DP-1204 |
| 8 Pigtails G652D 1m & 8 SC Adapters | OPVL-DP-1108 | OPVL-DP-1204 |
| 12 Pigtails G652D 1m & 12 SC Adapters | OPVL-DP-1112 | OPVL-DP-1204 |
| 16 Pigtails G652D 1m & 16 SC Adapters | OPVL-DP-1116 | OPVL-DP-1204 |
Technical Data
| Required Space envelope | H306 x W240 x D106(mm) |
| Number of in/out main cable port | 2 ports |
| Maximum main cable diameter | 15mm |
| Number of in/out drop cable port | 16 ports |
| Maximum in/out drop cable diameter | 7-9mm |
| Maximum number of customer feeds | 16 |
| Operating Temperature | +10 to + 70 DEG C |
| Material | ABS |
| Color | White RAL 9016 |
Logistics
| Packing Dimension | H320 x W250 x D110(mm) |
| Packet Weight (kg) | 1,8 |
| Net Weight (kg) | 1,7 |
| Installation Instruction included |
Optional Items
- Pigtails can be supplied with either SC/UPC or SC/APC connectors
- - Passive splitter in PLC form factor of 1x4 and 1x8
- - Adapter Couplers SC/APC or UPC
- - Fussion sleeve or splice protectors
- - Field termination kit SC
Gas Block
Introduction
GasBlock : is used whenthereis a need to block gas to pass freelyintodifferent micro-ductsections.
This could for example be necessary when changing from outdoor to indoor installations.
Application:
The Gas block connector works in a similar way as the standard connector when jointing micro ducts but has a compressible rubber gasket that is sealed after the cable has been installed.
Features:
•Easy “push-in” installation
•For 3 to 20 mm O.D. microducts •Material: Clear PC
•Leakage Pressure: 15 bar •Temperature Range: -10 ~60
In-Line Microduct Closure
Introduction:
It is designed by modular method to change the length of closure and branch direction. It is possible to assemble or dis-assemble
the closure without any special tools.
The maintenance of In-Line closure can be done without cutting the ducts,
and can be completed only by reopening upper modular part. In-Line closure is designed to connect several micro duct bundles and to branch-off tubes without any interruption of connectivity.
Application:
The branch closure is typically used in place of a microduct to protect the connector and the end cap for direct burial. Branch closure is designed to connect several microducts and to branch-off tubes without any interruption of connectivity. Using this closure, the ducts are protected and easy to reopen for maintenance.
Features:
The branch closure is tested for best functionality in combination with the air blown fibers unit and air blown fibers cables. ▪ Light weight
Easy installation
•Easy branching
•Microduct protection at joint/distribution point, can accommodate various types of microduct •Used for DB 5/3.5mm and TWD 7/3.5mm microducts
•Branch Closure has different types (6-way and 7-way types)
Reducers
Introduction:
MICRODUCT Accessories:
Microduct Reducer : connectors for quick and easy splicing of microducts allows interconnection between microducts
that are difference in outer diameters, the body is transparent for easy fault location during Installation,
to enable cable blowing, the Reducer connector is designed to operate at 15 bars without leakage. The Push-fit reducer connectors manufactured with high quality materials and transparent body assure easy and quick installation, connector can be re-used 10 times remaining maintained the high- performance requirements for air- blown installation systems.
Application:
The Reducer allows interconnection between microducts that are difference in outer diameters. Usually, this is used in the point of
transition from DB to DI microducts entering the office, house.
Features:
The reducer connectors are tested for best functionality in combination with the air blown fibers unit, and air blown fibers cables.
•Easy “push-in” installation
•For 3 to 20 mm O.D. microducts
•Material: Clear PC
•Leakage Pressure: 15 bar
•Negative Pressure: 750mm Hg ▪ Proof Pressure: 25 bar •Temperature Range: -10 ~60
Straight Connector
Introduction
Straight Connector: for quick and easy splicing of micro ducts, the body is transparent for easy fault location during Installation. To enable cable blowing, the connector is designed to operate at 15 bars without leakage The Push-fit straight connectors manufactured with high quality materials and transparent body assure easy and quick installation, connector can be re-used 10 times remaining maintained the high- performance requirements for air- blown installation systems.
Application:
The straight connectors for microducts provide a quick, easy and secure connection of
microducts, used to join sections of microducts..
Features
•Used for jointing two micro ducts.
Straight connector installation is simple and carried out in a few seconds.•Easy “push-in” installation
•Size (mm): For 3 to 20 mm O.D. microducts
•Material: Clear PC
•Leakage Pressure: 15 bar
•Negative Pressure: 750mm Hg
•Proof Pressure: 25 bar
•Temperature Range: -10 ~60
T-Type Microduct Closure
Introduction:
MICRODUCT Accessories:
It is designed by modular method to change the length of closure and branch direction. It is possible to assemble or disassemble the closure without any special tools.
The maintenance of T-branch closure can be done without cutting the ducts,
and can be completed only by reopening upper modular part.
T-branch closure is designed to connect two microduct bundles and to branch-off tubes without any interruption of connectivity.
Application:
The branch closure is typically used in place of a microduct to protect the connector and the end cap for direct burial. Rubber sealing cap consists of Main port and Distribution port, and
the Microduct, according to its different type and configuration, can be applied to different Rubber Sealing Cap
Features:
The branch closure is tested for best functionality in combination with the air blown fibers unit and air blown fibers cables. •Light weight
•Easy installation
•Easy branching
•Microduct protection at joint/distribution point, can accommodate various types of microduct •Used for DB 5/3.5mm and TWD 7/3.5mm microducts
•Up to DB 5/3.5mm 24way (OD:36.4mm) Up to TWD 7/3.5mm 12way (OD:30.0mm)
04.
ALROWAD SOLUTION
INJECTION
Alrowad company is specialized in manufacturing HDPE pipes from 32mm till 1200mm diameter with different pressure classes, It also offering welding and complementary items for polyethylene networks and supplies itsmachines and also train on its usage. Wherever your project is our solution will fit.
05.
ALROWAD SOLUTION
QATARAT
qatarat® is a product introduced to you by AlRowad Industrial Complex aiming to help cope with the growing water crisis, land reclamation, spread green areas around Egypt, and increase nutrition supply. With the continuous incline in population, and the new projects aiming at reclamation of the deserts, it’s now the time to apply a technology that’s well adapted to the scarcity of water and provides smarter and cheaper solutions for nutrition, and designed to survive harsh climates.
20 Years of Experience
With our 20 years of experience, we analyze your needs, and after a flawless production process, we deliver on the time we promised.
48000
90000
32
15000
OUR LATEST ARTICLES
23
Jul
Opening of Alrowad Complex for Complementary Industries
Refrancs
Alrowad Complex for Complementary Industries is one of the...
23
Jul
23
Jul
AlRowad Industrial Complex alliance with Telecom Egypt
is pleased to announce the supply of Microduct cables with a dedicated transmission fleet for ...
OUR PARTNERS
LET'S STAY IN TOUCH
Sign up to join our Newsletter , so that we reach out to you with our latest news